Start a tool. The gate on that branch opens. The collector starts. You keep your tools, your duct, your metal gates, and your collector. GRIT runs them from one Hub in your shop, with no subscription.
What happens when you make a cut
Picture a shop with a table saw, a planer, a collector in the corner, and a metal blast gate on each branch. Here is what happens when you make a cut.
-
Flip the saw on.
Same switch as always. The saw is plugged into a GRIT Trigger, and the Trigger is plugged into the wall.
-
The Trigger notices.
It feels the saw draw power and tells the Hub over a local radio mesh.
-
The Hub knows which gate.
You told it once in the GRIT App that this branch belongs to the saw.
-
The gate opens and the light turns green.
The Gate Control on that branch slides it open.
Green = open Red = closed -
The collector starts.
Only after the gate is open. The Collector Control turns it on the way you do now: at the plug, with its remote, or through its magnetic starter.
-
Turn the saw off.
The collector stops. If you set an off-delay, it runs a bit longer first to clear the duct.
Walk over to the planer and the same thing happens on the planer's branch. You never touch a gate or the collector switch.
The parts
One Hub, plus one part for each job in the shop.
Picking the right one
- Triggers: Match the tool's nameplate. 120V and 220V models up to 15A, Heavy Duty up to 35A.
- Gate Controls: 2.5 to 6 inch, sized to your gate. Fits standard metal blast gates.
- Collector Control: Match how your collector starts. 120V or 220V plug-in, IR/RF remote, or MagSwitch for magnetic starters.
- Power Banks: One covers about 10 gates. Add another past 100 ft of wire.
| Part | Where it goes | What it does |
|---|---|---|
| Hub GH-HU1001 | Near your router | Holds your shop's rules. Every GRIT part pairs to it. |
| Trigger | Between each tool and the wall | Tells the Hub when the tool starts. One per tool. |
| Gate Control | On each metal blast gate | Opens and closes the gate. Green = open, red = closed. |
| Collector Control | At your collector | Starts and stops the collector after the gate opens. |
| Power Bank GH-PB1003 | Near your gate run | Powers the Gate Controls on 12V wire. |
| Switch Trigger GH-TR5000 | On a wall dock | Handheld button for jobs with no tool plug. |
| Air Quality GH-AQ1002 | Where you breathe | Reads the air and runs your air cleaner. |
Will it reach across my shop?
One Hub runs a local radio mesh. Your Triggers, gates, and Collector Control talk to the Hub and to each other, so you do not run a control cable to every tool.
Each device can reach about 200 ft in open air. Real reach depends on your walls, what else is on the air, where things sit, and how many GRIT parts are powered nearby.
Clean air, too
The collector catches dust at the tool. The fine stuff that gets away hangs in the air after the cut. That is the air cleaner's job.
GRIT Air Quality reads the room and turns your air cleaner on when it gets dusty, then off when it clears, at the levels you set. A plug-in air cleaner, even a homemade one, runs through the included RF outlet.
Why it matters: fine wood dust in the home shop.
Start with two tools
Most shops start with the two tools they use every session. A saw and a planer. A bandsaw and a sander.
- 1 Hub
- 2 Triggers
- 2 Gate Controls
- 1 Collector Control
- 1 Power Bank
Add a tool later with one more Trigger and one more Gate Control. Nothing else changes.
Before you order
Have these handy
- A working collector and hard duct with metal blast gates, 2.5 to 6 inch, that slide freely.
- Each tool's nameplate: volts, amps, plug.
- How your collector starts: plug, remote, or magnetic starter.
- An outlet near your router for the Hub, and one near your gates for the Power Bank.
- A phone for the GRIT App.
Put those into the System Builder. It picks your parts, and if it is not sure about something, a person checks it instead of it guessing.
Still on flex hose with no gates? Start with small shop dust collection and duct layout and blast gate placement. Not sure it's time? See when to automate.
Setting it up
- Hub. Plug it in near your router, connect Ethernet or Wi-Fi, scan the QR code in the app. Under five minutes.
- Triggers. Tool into Trigger, Trigger into wall, pair it. Under two minutes each.
- Gate Controls. Bolt on the actuator, arm, and slide guide. Run the 12V wire to the Power Bank. Pair it and assign it to its tool. Watch Gate Control installation first.
- Collector Control. Plug-in models go between the collector and the wall. IR/RF models stick on near the collector's receiver and learn its remote. The MagSwitch Collector wires into the starter, so use a licensed electrician.
- Air Quality, if you want it. Set it where you breathe, power it, pair it, plug the air cleaner into the RF outlet, and set your levels.
What GRIT does not do
- Replace your collector. It runs the one you have.
- Sell blast gates. Gate Control bolts onto yours.
- Fix a weak system. Leaks, full bins, and clogged filters still cost suction. See lost suction and dust collector troubleshooting.
- Act as a safety system. It does not replace guards, a safety-rated stop, hearing or breathing protection, code wiring, or an electrician where you need one.
- Go past 6-inch gates. Bigger shop or a central system? See GRIT for larger systems.
Questions
What is GRIT at Home?
Dust collection automation for home woodshops. A Trigger on each tool tells a GRIT Hub in your shop when the tool starts. The Hub opens that tool's blast gate and starts your collector. It can also run an air cleaner from real air readings.
How does GRIT know which tool is on?
Each tool plugs into its own Trigger, which feels the tool draw power. You tell the Hub once, in the GRIT App, which gate goes with that tool.
How do I know a gate is open?
Look at the light on the Gate Control. Green is open. Red is closed. The GRIT App shows every gate too. More on telling if a blast gate is open.
What turns the dust collector on?
A Collector Control at the collector. The Hub turns the collector on after the gate is open and off when the tools tied to it stop. An off-delay can keep it running a set time to clear the duct and to go easy on motors that limit starts per minute. Which one you need depends on whether your collector starts from a plug, a remote, or a magnetic starter.
Can GRIT turn on my air cleaner?
Yes, with GRIT Air Quality. It reads the shop air and switches a compatible air cleaner through the included RF outlet when the air crosses the levels you set.
How do I run the collector for a floor sweep or the lathe?
Press the Switch Trigger. It opens the gate or gates you assigned and starts the collector.
Do I need an electrician?
Not for the plug-in parts. The Hub, Triggers, and plug-in Collector Controls plug into outlets, and Gate Controls bolt on and run on 12V wire. The MagSwitch Collector wires into a magnetic starter, and we recommend a licensed electrician for that.
Can I lock my tools so the kids can't turn them on?
Yes. GRIT Lock is built into the Hub. Lock the whole shop or just the tools you pick, so kids or grandkids cannot start a dangerous tool. It does not replace guards or a safety-rated stop. See how home shop locking works.
What is the smallest system that works?
One Hub, two Triggers, two Gate Controls, one Collector Control, and a Power Bank. See the starter system.
Ready to run your shop hands-free?
Start with two tools. Add the rest one at a time.
How GRIT works in a home shop
Start a tool. The gate on that branch opens. The collector starts. You keep your tools, your duct, your metal gates, and your collector. GRIT runs them from one Hub in your shop, with no subscription.
What happens when you make a cut
Picture a shop with a table saw, a planer, a collector in the corner, and a metal blast gate on each branch. Here is what happens when you make a cut.
-
Flip the saw on.
Same switch as always. The saw is plugged into a GRIT Trigger, and the Trigger is plugged into the wall.
-
The Trigger notices.
It feels the saw draw power and tells the Hub over a local radio mesh.
-
The Hub knows which gate.
You told it once in the GRIT App that this branch belongs to the saw.
-
The gate opens and the light turns green.
The Gate Control on that branch slides it open.
Green = open Red = closed -
The collector starts.
Only after the gate is open. The Collector Control turns it on the way you do now: at the plug, with its remote, or through its magnetic starter.
-
Turn the saw off.
The collector stops. If you set an off-delay, it runs a bit longer first to clear the duct.
Walk over to the planer and the same thing happens on the planer's branch. You never touch a gate or the collector switch.
The parts
One Hub, plus one part for each job in the shop.
Picking the right one
- Triggers: Match the tool's nameplate. 120V and 220V models up to 15A, Heavy Duty up to 35A.
- Gate Controls: 2.5 to 6 inch, sized to your gate. Fits standard metal blast gates.
- Collector Control: Match how your collector starts. 120V or 220V plug-in, IR/RF remote, or MagSwitch for magnetic starters.
- Power Banks: One covers about 10 gates. Add another past 100 ft of wire.
| Part | Where it goes | What it does |
|---|---|---|
| Hub GH-HU1001 | Near your router | Holds your shop's rules. Every GRIT part pairs to it. |
| Trigger | Between each tool and the wall | Tells the Hub when the tool starts. One per tool. |
| Gate Control | On each metal blast gate | Opens and closes the gate. Green = open, red = closed. |
| Collector Control | At your collector | Starts and stops the collector after the gate opens. |
| Power Bank GH-PB1003 | Near your gate run | Powers the Gate Controls on 12V wire. |
| Switch Trigger GH-TR5000 | On a wall dock | Handheld button for jobs with no tool plug. |
| Air Quality GH-AQ1002 | Where you breathe | Reads the air and runs your air cleaner. |
Will it reach across my shop?
One Hub runs a local radio mesh. Your Triggers, gates, and Collector Control talk to the Hub and to each other, so you do not run a control cable to every tool.
Each device can reach about 200 ft in open air. Real reach depends on your walls, what else is on the air, where things sit, and how many GRIT parts are powered nearby.
Clean air, too
The collector catches dust at the tool. The fine stuff that gets away hangs in the air after the cut. That is the air cleaner's job.
GRIT Air Quality reads the room and turns your air cleaner on when it gets dusty, then off when it clears, at the levels you set. A plug-in air cleaner, even a homemade one, runs through the included RF outlet.
Why it matters: fine wood dust in the home shop.
Start with two tools
Most shops start with the two tools they use every session. A saw and a planer. A bandsaw and a sander.
- 1 Hub
- 2 Triggers
- 2 Gate Controls
- 1 Collector Control
- 1 Power Bank
Add a tool later with one more Trigger and one more Gate Control. Nothing else changes.
Before you order
Have these handy
- A working collector and hard duct with metal blast gates, 2.5 to 6 inch, that slide freely.
- Each tool's nameplate: volts, amps, plug.
- How your collector starts: plug, remote, or magnetic starter.
- An outlet near your router for the Hub, and one near your gates for the Power Bank.
- A phone for the GRIT App.
Put those into the System Builder. It picks your parts, and if it is not sure about something, a person checks it instead of it guessing.
Still on flex hose with no gates? Start with small shop dust collection and duct layout and blast gate placement. Not sure it's time? See when to automate.
Setting it up
- Hub. Plug it in near your router, connect Ethernet or Wi-Fi, scan the QR code in the app. Under five minutes.
- Triggers. Tool into Trigger, Trigger into wall, pair it. Under two minutes each.
- Gate Controls. Bolt on the actuator, arm, and slide guide. Run the 12V wire to the Power Bank. Pair it and assign it to its tool. Watch Gate Control installation first.
- Collector Control. Plug-in models go between the collector and the wall. IR/RF models stick on near the collector's receiver and learn its remote. The MagSwitch Collector wires into the starter, so use a licensed electrician.
- Air Quality, if you want it. Set it where you breathe, power it, pair it, plug the air cleaner into the RF outlet, and set your levels.
What GRIT does not do
- Replace your collector. It runs the one you have.
- Sell blast gates. Gate Control bolts onto yours.
- Fix a weak system. Leaks, full bins, and clogged filters still cost suction. See lost suction and dust collector troubleshooting.
- Act as a safety system. It does not replace guards, a safety-rated stop, hearing or breathing protection, code wiring, or an electrician where you need one.
- Go past 6-inch gates. Bigger shop or a central system? See GRIT for larger systems.
Questions
What is GRIT at Home?
Dust collection automation for home woodshops. A Trigger on each tool tells a GRIT Hub in your shop when the tool starts. The Hub opens that tool's blast gate and starts your collector. It can also run an air cleaner from real air readings.
How does GRIT know which tool is on?
Each tool plugs into its own Trigger, which feels the tool draw power. You tell the Hub once, in the GRIT App, which gate goes with that tool.
How do I know a gate is open?
Look at the light on the Gate Control. Green is open. Red is closed. The GRIT App shows every gate too. More on telling if a blast gate is open.
What turns the dust collector on?
A Collector Control at the collector. The Hub turns the collector on after the gate is open and off when the tools tied to it stop. An off-delay can keep it running a set time to clear the duct and to go easy on motors that limit starts per minute. Which one you need depends on whether your collector starts from a plug, a remote, or a magnetic starter.
Can GRIT turn on my air cleaner?
Yes, with GRIT Air Quality. It reads the shop air and switches a compatible air cleaner through the included RF outlet when the air crosses the levels you set.
How do I run the collector for a floor sweep or the lathe?
Press the Switch Trigger. It opens the gate or gates you assigned and starts the collector.
Do I need an electrician?
Not for the plug-in parts. The Hub, Triggers, and plug-in Collector Controls plug into outlets, and Gate Controls bolt on and run on 12V wire. The MagSwitch Collector wires into a magnetic starter, and we recommend a licensed electrician for that.
Can I lock my tools so the kids can't turn them on?
Yes. GRIT Lock is built into the Hub. Lock the whole shop or just the tools you pick, so kids or grandkids cannot start a dangerous tool. It does not replace guards or a safety-rated stop. See how home shop locking works.
What is the smallest system that works?
One Hub, two Triggers, two Gate Controls, one Collector Control, and a Power Bank. See the starter system.
Ready to run your shop hands-free?
Start with two tools. Add the rest one at a time.